S-110 Medien- & -Rate-Konverter
10/100Base-TX zu 100Base-X Konversion

- 10/100Base-TX-zu-100Base-X LWL Medienkonverter
- Netzwerkdistanzen bis zu 120 km
-
Erweiterte Funktionen - Link-Pass-Through,
Far-End Fault, Auto-MDIX und Loopback
Die funktionsreiche Reihe der 10/100 LWL Medienkonverter von Perle verbindet 10/100 Ethernet und LWL / Glasfaser transparent. Unsere 10/100-Konverter stellen eine wirtschaftliche Möglichkeit dar, die Reichweite eines bestehenden Netzwerks zu vergrößern, die Lebensdauer von Einrichtungen ohne LWL (Glasfaser) zu verlängern oder die Entfernung zwischen zwei Geräten zu vergrößern. S-110 Medienkonverter mit Support für Power over Ethernet (PoE) und erweiterten Temperaturbereich sind erhältlich.
Mit den erweiterten Perle-Funktionen wie Autonegotiation, Auto-MDIX, Link-Pass-Through, Far-End Fault und Remote-Loopback können Netzwerkadministratoren "alles sehen". Dadurch ist eine effizientere Fehlerbehebung möglich und weniger Wartungsarbeit vor Ort notwendig. Diese Kosten und Zeit sparenden Funktionen sowie eine lebenslange Garantie und kostenloser technischer Support weltweit machen die 10/100 Ethernet Medienkonverter von Perle zur besten Wahl für IT-Profis.
Funktionen der 10/100 zu LWL Medienkonverter
Auto-Negotiation (802.3u) | Der Medienkonverter unterstützt die Autonegotiation an der 10/100Base-TX-Schnittstelle. |
Auto-MDIX | Auto-MDIX (Automatic Medium-Dependant Interface Crossover) erkennt die Signale an der 1000Base-T-Schnittstelle, um zu bestimmen, welcher Kabeltyp angeschlossen ist (Straight-Through oder Crossover) und konfiguriert die Verbindung automatisch, wenn diese Funktion aktiviert ist. Wenn Auto-MDIX aktiviert ist, kann entweder ein Straight-Through- oder ein Crossover-Kabel verwendet werden, um den Medienkonverter mit dem Gerät am anderen Ende des Kabels zu verbinden. |
Link Pass-Through |
Mit der Link-Pass-Through-Funktion wird der Status des UTP-Receivers an den LWL / Glasfaser-Transmitter übergeben, um den Medienkonverter für die angeschlossenen Endgeräte transparent zu machen. Wenn Far-End Fault aktiviert ist, kann der Medienkonverter außerdem den 10/100Base-TX-Transmitter ausschalten, wenn ein FAR-End Fault empfangen wird. Die Verwendung von Link-Pass-Through zusammen mit Far-End Fault minimiert im Fehlerfall Datenverluste. Sollte ein Fehler auftreten, steht den Endgeräten eine Fehleranzeige zur Verfügung, wodurch die Fehlerbehebung vereinfacht wird. |
Far-End Fault (FEF) |
Der Medienkonverter implementiert den Standard 802.3 für Far-End Fault, um Remotefehlerbedingungen bei der 100Base-X-LWL Verbindung anzuzeigen und zu erkennen. Wenn Far-End Fault aktiviert ist, überträgt der Medienkonverter die Far-End Fault-Anzeige über die 100Base-X- LWL Verbindung, wenn ein Empfangsfehler bei der 100Base-X- LWL Verbindung erkannt wird. Der Medienkonverter überprüft die 100Base-X- LWL Verbindung kontinuierlich auf ein gültiges Signal. Welche Aktion der Medienkonverter beim Empfang einer Far-End Fault-Anzeige ausführt, richtet sich nach der Einstellung für den Link-Pass-Through-Schalter. |
Pause (IEEE 802.3xy) | Pause-Signalisierung ist eine IEEE-Funktion, die die Datenübertragung zwischen zwei Geräten zeitweilig aussetzt, falls eines der Geräte überlastet ist. Der Fast Ethernet Medienkonverter unterstützt die Pause-Negotiation für die 100Base-TX-Kupferkabelverbindung. |
VLAN | Der Medienkonverter ist für VLAN-getaggte Pakete transparent. |
Remote LoopBack | Der Medienkonverter kann am LWL Port einen Loopback ausführen. |
Nicht das, was Sie suchen? Alle LWL Medienkonverter von Perle anzeigen.
Benötigen Sie Hilfe? Kontakt zu Perle.
Hardware Specifications
Power | |
---|---|
Input Supply Voltage | 6 - 30 vDC, unregulated (12 vDC Nominal) |
Current | 175 mA |
Power Consumption | 2.1 watts |
Power Connector | 5.5mm x 9.5mm x 2.1mm barrel socket |
Power Adapter | |
Universal AC/DC adapter | 100-240v AC, regulated DC adapter included |
Indicators | |
Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received. |
Copper link on / Receive activity (LKC) | This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received. |
Fiber Duplex (FDF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is operatinal in full duplex mode. The LED is off when in half duplex. |
Copper Duplex (FDC) | This green LED is operational only when power is applied. The LED is on when the 10/100Base-TX link is operatinal in full duplex mode. The LED is off when in half duplex. |
10/100 Speed | This green LED is operational only when power is applied. The LED is on when the speed of the copper Ethernet port is running at 100 MBPS. The LED is off when in 10 MBPS |
Switches - accessible through a side opening in the chassis | |
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter
uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to
advertise full duplex.
Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Pass Through | Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. |
Far-End Fault (FEF) | Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received.
Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
Remote Loopback | The media converter can perform a loopback on the 100Base-X fiber interface.
Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Duplex Fiber | Full (Default) Half |
Connectors | |
100Base-TX | RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation | 1.5kv |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 512 Kbits frame buffer memory |
Size | Maximum frame size of 2048 bytes |
Environmental Specifications | |
Operating Temperature | 0 C to 50 C (32 F to 122 F) |
Storage Temperature | minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output (BTU/HR) |
7.2 |
MTBF (Hours)** | Without power adaptor: 598,000 With power adaptor: 334,000 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.3 kg, 0.66 lbs |
Dimensions | 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches |
Packaging | |
Shipping Weight | 0.55 kg, 1.2 lbs |
Shipping Dimensions | 170 x 280 x 70 mm, 6.7 x 10.2 x 2.8 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class B*, EN55022 Class B* |
CISPR 22 Class B* CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 |
UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|
CE | |
Laser Safety | EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
* When used with a Class B rated AC power adapter.
**Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Select a Model to obtain a Part Number - Unmanaged Stand-alone Media Converters - Fast Ethernet to Fiber
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-M2ST2 | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2SC2 | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2LC2 | Dual LC |
100Base-FX |
-20.0 |
-12.0 |
-30.0 |
-14.0 |
10.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-S2ST20 | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2SC20 | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2LC20 | Dual LC |
100Base-LX |
-15.0 |
0.0 |
-34.0 |
-5.0 |
19.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2ST40 | Dual ST |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-110-S2SC40 | Dual SC |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-110-S2LC40 | Dual LC |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-110-S2ST80 | Dual ST |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-110-S2SC80 | Dual SC |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-110-S2LC80 | Dual LC |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-110-S2ST120 | Dual ST |
100Base-ZX |
0.0 |
5.0 |
-35.0 |
-3.0 |
35.0 |
1550 |
SMF |
120 km (75 mi) |
S-110-S2SC120 | Dual SC |
100Base-ZX |
0.0 |
5.0 |
-35.0 |
-3.0 |
35.0 |
1550 |
SMF |
120 km (75 mi) |
S-110-S2LC120 | Dual LC |
100Base-ZX |
0.0 |
5.0 |
-34.0 |
-3.0 |
34.0 |
1550 |
SMF |
120 km (75 mi) |
Single Fiber Models Recommended use in pairs
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-M1ST2U | Single ST |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km (1.2 mi) |
S-110-M1ST2D | Single ST |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km (1.2 mi) |
S-110-M1SC2U | Single SC |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km (1.2 mi) |
S-110-M1SC2D | Single SC |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km (1.2 mi) |
S-110-S1ST20U | Single ST |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-110-S1ST20D | Single ST |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
S-110-S1SC20U | Single SC |
100Base-BX-U |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-110-S1SC20D | Single SC |
100Base-BX-D |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
S-110-S1SC40U | Single SC |
100Base-BX-U |
-8.0 |
-3.0 |
-33.0 |
-3.0 |
25.0 |
1310 / 1550 |
SMF |
40 km (25 mi) |
S-110-S1SC40D | Single SC |
100Base-BX-D |
-8.0 |
-3.0 |
-33.0 |
-3.0 |
25.0 |
1550 / 1310 |
SMF |
40 km (25 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 62.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |